Here are simple, step-by-step instructions for adjusting a top shaped with darts to fit a smaller bust.
If you find that tops tend to sag over the bust, but fit well elsewhere, then this adjustment will help you to tailor the fit exactly where you need it. We also discuss changing the position of the dart based on your specific measurements - sometimes the adjustment may be as simple as moving the dart up or down so that it sits at the right position for your body.
Making pattern adjustments may seem a bit daunting at first, but the effort is completely worth it to achieve a beautiful, handmade garment with a custom fit.
MaterialsGather some basic materials to adjust the pattern pieces:
- Top Front pattern piece (we're using the Scenic Top)
- measuring tape
- scrap paper
To determine the size of adjustment necessary, measure your high bust and full bust.
The high bust measurement is taken around the body, with the tape snugged up to the underarms, and above the breasts.
The bust measurement is taken around the fullest part of the breasts.
Compare your body measurements to the size chart in the pattern tutorial.For example:
|Size H||Your body measurement|
|High Bust measurement||34" (86cm)||34" (86cm)|
|Full Bust measurement||36" (91cm)||35" (96cm)|
The bust apex is marked on the pattern. It is a good idea to measure your own bust apex to make sure the bust dart ends up in the correct position for your body. This is a minor adjustment that can have a bit impact on the fit of the finished garment.
To find your bust apex, measure from your shoulder (the position where a shoulder seam line would sit) to the centre of your bust - this is the part that points out the most. Note that the bust apex is not necessarily the same as your nipple position. We recommend taking this measurement while wearing your favourite underwear.
Check your measurement against the pattern.
Keep a note of the difference between your bust position versus the pattern. For example:
|Pattern||= 9.8" (25cm)|
|Your Bust Position||= 8.8" (22.5cm)|
|Difference||= 1" (2.5cm)|
Small Bust Adjustment
Adjust pattern pieces
1. Begin by drawing cut lines on the Front pattern piece:a. Line parallel to Centre Front (CF) from the hem to the end of the dart (line a on diagram below).
b. Line at right angles to CF from the dart end to CF line (line b on diagram).
c. Line through centre of dart to dart point (line c on diagram).
d. Line from dart end to stitch line of armhole seam (line d on diagram).
2. Cut the pattern along these lines, keeping the pivot points intact at dart end and armhole seam (see diagram above for location of pivot points). If you accidentally snip through the pivot point, use some tape to create a hinge.
Be sure to mark the original dart end so you don't lose it in the changes. This is VERY important.
For the following steps, it is a good idea to position your pattern piece over a larger piece of paper, so that once the adjustments are made, you can cut around the entire finished piece. This prevents things from shifting around so much.
3. Secure the top section of the pattern piece with tape, then draw a line extending the CF edge below the pattern piece.
Now, apply your full bust difference to the pattern. In our example, the full bust difference is 1" (2.5cm). Divide the difference in half: for example 1" (2/5cm) / 2 = 1/2" (1/25cm) because we are working on half of the front piece.
Slide the side section in by your calculated difference: our example is 1/2" (1.25cm). Let the dart and armhole pivot - the side will move up and the dart will close.
4. Slide the centre section up by half the amount the side section slid out in the previous step, so 1/4" (6mm), along the CF line you drew earlier.
5. Redraw the dart stitching lines so that they meet at the point of the original dart end (note that for a Small Bust Adjustment, the dart end may slide underneath the pattern piece).
6. Blend the hem and smooth the armhole if needed.
7. The adjustment is complete, however, if the location of your Bust Apex is different than the pattern, we'll continue below with a few more steps.
Modifying the Bust Apex
The dart should be positioned so that it points directly towards the Bust Apex. It may be necessary to move the dart up or down so that it is positioned correctly. This adjustment may be all that is needed to improve the fit of a top with dart shaping.
1. Cut two lines at right angles to the Centre Front Line, above and below the dart.
2. Slide the darted section down or up by the difference. In the example above, we calculated the difference as 1" (2.5cm) higher, so we will slide the piece up by that amount.
3. Blend the side seam on both sections.
4. Your pattern piece is now ready to use!
Remember, we always recommend sewing a muslin to test out your pattern adjustment before cutting into your fancy fabric.
If you have any questions about sewing or making adjustments to the Scenic Top, please feel free to join us at the Twig + Tale Facebook group.
Read more pattern adjustment tutorials here: